Results 1 to 10 of 26

Thread: Use nzTivo Image (based on 1.5) or OzTivo 1.6.2 ??

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Aug 2007
    Location
    Christchurch
    Posts
    51
    Ok, I've tried those suggestions:

    I ran palmod_config and selected the NZ frequency table. Before this, I was (probably coincidentally) getting one channel - TV2. After, I am getting no channels. So I don't think I am doing anything wrong - I think the Christchurch postcode has been fully implemented in ozTivo 1.6.2 (which is confirmed by below).

    I edited /etc/postcodezones and added Christchurch (02123). /bin/ntpdate ... does not have the error now, but it does say "Failed to connect to any of the time servers". I guess it doesn't work with a modem. Back in tivo, time is still wrong. I didn't wait for a daily update (because is not modem not connecting now), but I suspect that is would have change the time then). So I think this is fixed (someone may want to add the Christchurch postcode to the next ozTivo image release).

    I double-checked the modem settings, and it seems like it should work, but it doesn't. I even put the tivo hdd back in my pc and re-did the settings through knoppix (setting the emulator doesn't crash there). However, when I looked at the changes it made, they were the same as nic_config_tivo - even the emulator adrress had been changed to 127.0.0.1 in tclient.conf. Maybe the address doesn't matter there, because the correct nz emulator IP is in oztivo.conf. Anyway, I even tried a second ISP, but had the same problem. As my modem worked before nic_config_tivo, I think this is a problem with nic_config_tivo - maybe when it failed, or maybe when changing from turbonet to modem, there is something it forgets to change. But I guess as modem is not supported, maybe I can't hope for too much.

    And then I used nic_config_tivo to setup TurboNet use instead of modem. I could telnet in over lan, establish an ftp connection on ftp://tivo'siIP, but going to TivoWebPlus at http://tivo'siIP did not work. After less than 30 minutes usgin LAN, my tivo started crashing - remote did not work, telnet connection stopped responding and the subtle moving graphics in the background stopped moving. After a hard reset it worked for a few minutes and then crashed again. After another hard reset it only lasted for about 10 seconds. I'm guessing that is a problem with my turbonet card rather than the ozTivo image.

    US Phillips HDR112 TIVO, TurboNet, PAL Tuner, 80gb HDD. Work, Fun.

  2. #2
    Join Date
    May 2004
    Location
    Victoria
    Posts
    1,239
    "crash" as in freeze or reboot?

    If you mean freeze then edit the /etc/oztivo.conf file from timing=3 to timing=16 and try again. I *think* the nz image still has an oztivo.conf file. You could also try using nic_config_tivo and altering the timing setting there but the current oztivo image has issues with the setting actually changing. Not sure about the nz image but worth a shot I suppose.

    If you mean reboot then I have no idea.
    Last edited by Darren King; 14-08-2007 at 08:31 PM.
    Darren King
    OzTiVo Repairs and Modifications
    If your TiVo requires repairs or modifications
    then visit: http://kingey1971.wix.com/tivorepairs

    NOW ALSO REPAIRING FETCH TOO!

  3. #3
    Join Date
    Aug 2007
    Location
    Christchurch
    Posts
    51
    Quote Originally Posted by Darren King View Post
    "crash" as in freeze or reboot?...
    As in freeze. I did choose "Failsafe" in nic_config_tivo which is "16" from memory, but the setting changes you say? Well, I've re-imaged and now I don't want to touch nic_config_tivo because that seems to make the modem fail permanently, regardless of later editing of the conf files or re-running nic_config_tivo

    So far, I have only used the ozTivo image.

    US Phillips HDR112 TIVO, TurboNet, PAL Tuner, 80gb HDD. Work, Fun.

  4. #4
    Join Date
    May 2004
    Location
    Victoria
    Posts
    1,239
    Quote Originally Posted by NoSignal View Post
    As in freeze. I did choose "Failsafe" in nic_config_tivo which is "16" from memory, but the setting changes you say? Well, I've re-imaged and now I don't want to touch nic_config_tivo because that seems to make the modem fail permanently, regardless of later editing of the conf files or re-running nic_config_tivo

    So far, I have only used the ozTivo image.
    Well if you want to stop the freezing you *HAVE* to alter the timing setting. I can't see how manually editing the oztivo.conf file would upset your modem connection but if you are that afraid then you have no choice but to unplug the network cable to stop the freezing.
    Darren King
    OzTiVo Repairs and Modifications
    If your TiVo requires repairs or modifications
    then visit: http://kingey1971.wix.com/tivorepairs

    NOW ALSO REPAIRING FETCH TOO!

Similar Threads

  1. Testing latest nztivo Dec06RC1 UK image
    By slangnz in forum New Zealand General Forum
    Replies: 5
    Last Post: 03-08-2008, 09:15 PM
  2. oztivo image
    By framtech in forum Software Upgrades/Mods
    Replies: 4
    Last Post: 20-07-2008, 10:19 PM
  3. I need the Old Oztivo Image
    By Videoguy in forum Question and Answer Forum
    Replies: 0
    Last Post: 16-01-2008, 09:13 AM
  4. Getting nzTivo Thomson Dec06 RC1 image & Turbonet Card working
    By fairyland in forum New Zealand General Forum
    Replies: 14
    Last Post: 24-05-2007, 11:56 AM
  5. oztivo image in USA
    By tappy in forum Question and Answer Forum
    Replies: 1
    Last Post: 17-11-2006, 08:49 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •