whats the emulator for south australia???

[vex]

thanks all fixed !

[Darren King]

If you are using the OzTiVo image there is no need to change anything. Minnie is the emulator for ALL of Australia which is default set on the install image, and it picks your lineup based on the answers you give to the questions during Guided Setup as per the online setup guide on the OzTiVo website. If you are getting connection failures then I would be looking at network hardware faults, network blockages (firewall, perhaps?) or something your ISP has done that is refusing connection.

[vex]

thanks for the reply darren i was gunna email ya cause i have no joy

i beleive no changes needed but

with no changes i put in 05000 for zip code and 008 for area
it will fail connecting saying failed service

have made umteem changes to tclient.conf and no change after reboot
everytime

i changed /etc/rc.d/rc.sysinit.author to
/hack/bin/emuProxy2 -s 210.48.107.133 -p 8000 &
and redid guided setup after reboot and i connected and downloaded & indexd
but said no dailup numbers available and no cable services in your area try a reighbouring zip code ???????????????????

im stuck mate please help

[vex]

this is the tclient.conf changed back to orig


# This is the default port, it's values come from Addr.itcl not here
#
000:
# Dennis' Emulator
126::66.23.218.193:80:::
# This is for the server emulator on minnie. Trouble if your ISP blocks HTTP .9
#127::131.244.9.101:80:::
is hashed here is this right??


# This uses emuProxy2 to avoid problems with transparent proxy. Thanks Tim!
127::127.0.0.1:8000:::

will not connect but i can ping it with no port80 at command prompt
but with port 80 i get connection refused???

does this help ???

[Darren King]

Sorry, but I'm not a software person. What I said in my above post stands in that if you are getting a failed connection when trying it is something network related. The rest I can't help with.

Also you cannot ping Minnie. It is set up not to respond to pings. You should be able to ping your TiVo however with no reference to any ports, just your internal network IP address it is using.

[vex]

thanks darren im no software person ither

but it is strange i can connect using

/hack/bin/emuProxy2 -s 210.48.107.133 -p 8000 & edited in rc.sysinit.author

but the orig will fail

is there a way to test if i have isp prob or if the emulator is connecting

cause all seems ok internally i can telnet and get tivoweb and ftp no probs
i have to do this to edit the configs

i am really lost ???

[petestrash]

Did you choose "Antenna" as your source?

Peter.

[Darren King]

thanks darren im no software person ither

but it is strange i can connect using

/hack/bin/emuProxy2 -s 210.48.107.133 -p 8000 & edited in rc.sysinit.author

but the orig will fail

is there a way to test if i have isp prob or if the emulator is connecting

emuProxy2 has something to do with transparent proxy and your ISP and this proves a clue. Petestrash is the better person to help and he usually jumps on later in the evening. I'll pre-empt that he will probably ask you to post your tclient.log which should give some more insight.

Edit: nevermind... the cavalry has arrived (thanks Peter!)

[vex]

ok thanks darren you where right

i reconfigured my home network to use a sa based 33.6 internet connection instead of the dsl and lookout it worked fine retry couple of times cause of speed but it worked so it is an isp problem

peter has helped before so i hope he can answere the question

i know my isp provider personally so what can i ask him to turn on or configure to get my dsl conection to work with tivo

am still unsure of the ips in rc.sysinit.author & tclient.conf which one or collection of am i using ????

thanks for all the help given in past and future

thankgod im up and running :-)

paste if helps??

# This is the default port, it's values come from Addr.itcl not here
#
000:
# Dennis' Emulator
126::66.23.218.193:80:::
# This is for the server emulator on minnie. Trouble if your ISP blocks HTTP .9
#127::131.244.9.101:80:::

# This uses emuProxy2 to avoid problems with transparent proxy. Thanks Tim!
127::127.0.0.1:8000:::

end

[petestrash]

What you have posted is correct for tclient.conf (if using emuProxy2).

As Darren has already suggested, force a dailycall (using DSL) and then post the first 20-30 lines from tclient.log or otclient.log so we can see what is happening, and where it is failing.

also make sure your rc.sysinit.author still has:
emuProxy2 -s 131.244.9.101 &

In the emuproxy section.

Peter.