Results 1 to 2 of 2

Thread: Startup screen not showing

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1

    Startup screen not showing

    Hi,

    I installed my Phillips S1 HDRx12 Tivo a few days ago (using image from 31st of March 2005). Everything is working fine except that I never see the OzTivo startup screens when it boots - the ones that say "Welcome to Maintenance Mode" or "Startup up..." with the OzTivo logo.

    Has anyone else seen or heard of this? Is this a problem with the new image?

    It's no problem in itself except that it can confuse a Tivo newbie like myself. I initially thought there was something wrong with my Tivo because the picture was jerky and yet the startup screen didn't say "Welcome To Maintenance Mode." [That problem obviously fixed itself when I rebooted the unit a couple of times the next day and it did finally leave maintenance mode.]

    What commands can I execute to determine if the correct screen is actually present on the disk?

    Robert.

  2. #2
    Join Date
    May 2004
    Location
    Victoria
    Posts
    1,239
    Hi Robert

    It was an issue with the February release of the beta 1.4 image. The screens were not put in the right spot or something like that. The issue has been documented and images are available from the quote below from the OzTiVo email list (not these forums):

    To: oztivo email list at www.oztivo.com
    Subject: [oztivo] Missing Startup screens for beta Release 1.4 (22/02/05)


    As anyone who has loaded Oztivo beta release 1.4 will know, the startup
    screens do not show during boot so you do not know whether you are going to
    be in maintenance or regular PAL mode until it has finished booting.


    I have uploaded the startup screens that I use for this release to:
    http://minnie.tuhs.org/twiki/pub/Upl...n2Version7.zip


    If you like you can use these as temporary fillers until Ed uploads the
    official ones (They do say release 4 instead of 1.4, but at least they work
    and it easy for me to see which version is installed).


    I have added the Instructions for loading the images and other issues with
    this beta release to the page below:
    http://minnie.tuhs.org/twiki/bin/vie...ntImageRelease


    Feel free to add/change anything.

    As you can see Minnie (the name of the oztivo website) has the procedure if you wish to try that.

    If you do not wish to install the images then the easiest way is to use TiVoWEB and go into the PAL/NTSC switcher section. If you see GS=0 then you are in normal mode. If you see GS=1 then you are in Maintenance Mode. Typically you will never be in Maintenance Mode unless you have just done the guided setup.

    The release of the final image will not have this issue, nor does the V1.3 release of OzTiVo software which has been around for well over a year. There is also a later version of the beta 1.4 image (1st April) than you have used.
    Last edited by Darren King; 08-04-2005 at 01:14 PM.
    Darren King
    OzTiVo Repairs and Modifications
    If your TiVo requires repairs or modifications
    then visit: http://kingey1971.wix.com/tivorepairs

    NOW ALSO REPAIRING FETCH TOO!

Similar Threads

  1. Tivo Series 1 Startup Sequence
    By Islander in forum Question and Answer Forum
    Replies: 1
    Last Post: 02-07-2014, 07:41 PM
  2. Tivo showing GMT time
    By jcurrey in forum Question and Answer Forum
    Replies: 5
    Last Post: 12-08-2008, 06:21 PM
  3. Tivo Freezes on Startup..
    By star in forum Question and Answer Forum
    Replies: 5
    Last Post: 22-02-2007, 04:29 PM
  4. Can I fix the startup animation without a NIC?
    By Doitsujin in forum Question and Answer Forum
    Replies: 15
    Last Post: 13-02-2007, 09:08 PM
  5. ToDo list not showing?
    By mr_gibbon in forum Question and Answer Forum
    Replies: 0
    Last Post: 24-11-2006, 05:54 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •