PDA

View Full Version : Video output settings won't save



jeremyl
29-04-2010, 10:34 AM
Wanting to pick your collective brain – I recently had the hard disk replaced in my TiVo, because the existing one failed. I've noticed that since replacing the hard disk, my unit won't save my video output settings.

I change it so that it outputs 1080i fixed (for some reason it defaults to 576p), but if I turn off my television and turn it back on again (leaving the TiVo on all the time obviously), the TiVo has reverted to 576p. Any ideas what could be causing this?

I didn't think it could be related to the HD replacement, but the only other person I've come across (on the whirlpool forums) who is also having this problem has also recently upgraded to a 1TB hard disk.

Cheers

petestrash
30-04-2010, 12:24 AM
Has the setting itself reverted if you go back to the menu, or is it just showing 575p while still set on 1080i?

Peter

j30max
01-05-2010, 11:15 AM
also, are you using HDMI or composite connections?

petestrash
01-05-2010, 01:32 PM
Perhaps you meant HDMI or Component?

Composite cannot show a 1080i signal.

Peter.

j30max
06-05-2010, 04:24 PM
perhaps I did :-)

you know what i mean.

jeremyl
10-05-2010, 03:07 PM
The setting itself has reverted.


Has the setting itself reverted if you go back to the menu, or is it just showing 575p while still set on 1080i?

Peter

jeremyl
10-05-2010, 03:08 PM
also, are you using HDMI or composite connections?

Using HDMI

Skolink
11-08-2013, 01:39 PM
On a similar note, is there a trick to getting 1080i over component?

The TiVoHD will output only 576i over component, but will output all/any resolutions including 1080i over HDMI. I've tried native, hybrid, fixed in various resolutions. The setting changes on the front display and in the menus but the component output does not change.

If I reboot the TV flicks up 1080i very briefly immediately before the intro video but then goes back to 576i.

I'm a bit short of HDMI inputs on the TV, so 1080i over component would be useful.

Islander
11-08-2013, 02:35 PM
I suspect that getting 1080i is disabled via the component outputs to prevent illegal copying to dvd.

Skolink
11-08-2013, 05:43 PM
Possibly, but TiVoHD isn't Freeview approved so there is no requirement for them to do so.
Peter specifically says here (http://forums.oztivo.net/showthread.php?2002-Tivo-HD-Video-quality&goto=post#2) that he uses 1080i over component.

petestrash
12-08-2013, 01:51 PM
The Tivo HD is Freeview licensed in Australia, which is one of the reasons 30 second skip was disabled and fast forward speed reduced.

I stopped using Component years ago, but just dragged the cables out, to see if anything has changed in newer firmware. When the TiVo is set to fixed 1080i, I can confirm that I still get 1080i using component in Australia.

It is possible when setup for NZ that this may have been be restricted by TVNZ?

Peter.

Skolink
12-08-2013, 07:16 PM
Thanks for testing that Peter.

alvittos
06-08-2014, 09:51 PM
are you using HDMI or composite connections?

Skolink
07-08-2014, 07:45 AM
are you using HDMI or composite connections?

Who me? did you read the whole thread?
I am currently using HDMI so that we get 1080i, but it means I have to swap inputs whenever I plug in the PC. Our second TiVoHD is being loaned out, so it isn't such an issue, but I would still like to get 1080i over component working.

I just saw your other post re setting up with the OzTiVo image. This thread is referring to the Series 3 TiVoHD digital DVB-T TiVo, not the older series 1 analog TiVo.

...And then I saw your other post and realised you are a bot regurgitating other's posts.