PDA

View Full Version : Time an hour out



ajharvey
16-05-2007, 08:20 PM
It appears that since daylight savings time stopped the time on my TiVo (Thompson, RC1 image) has been an hour out - I didn't notice until recently because the guide data is similarly transposed, so everything has been recording just fine. I've tried both a reboot and a power off, but neither make any difference. Any clues?

TimesOwn
17-05-2007, 05:40 PM
Have you tried running "fixtivotime " from the command window?

ajharvey
20-05-2007, 08:03 PM
Have you tried running "fixtivotime " from the command window?
No, I hadn't....
But I have now - It found an NTP server on second try but the problem still remains.
Incidentally, date on the console shows the correct time, and did before I ran fixtivotime (I thought a before & after might be useful...) but the UI still shows the wrong time.

petestrash
21-05-2007, 01:33 AM
What result do you show when trying
/bin/ntpdate -vb 132.163.4.103

Peter.

Wanted
21-05-2007, 05:03 AM
Normally if you change the time you need to reboot once or twice before it changes it properly in my experience.

ajharvey
27-05-2007, 10:09 AM
What result do you show when trying
/bin/ntpdate -vb 132.163.4.103

Peter.
[TiVo [p0] ~]# /bin/ntpdate -vb 132.163.4.103
[TiVo [p0] ~]# Time set to: Sun May 27 13:07:30 2007
Have a nice day.

Several reboots and power-offs have had no effect either... a strange mystery...

petestrash
27-05-2007, 03:51 PM
I suspect you may be using an outdated ntpdate and/or your postcodezones files is not correct.

To test your current postcodezone file type the following and show the results:
cat -et /etc/postcodezones

If you want to load a good one, upload from:
ftp://orac.caffeine.co.nz/install/postcodezones Update: use the postcodezones file attached 2 messages below.

I have attached the latest ntpdate.

Peter.

Islander
27-05-2007, 05:18 PM
If you want to load a good one, upload from:
ftp://orac.caffeine.co.nz/install/postcodezones



Please note that the list in the above file is not complete for NZ Ref: http://forums.oztivo.net/showpost.php?p=8835&postcount=2.
If you use any of the codes not in the file above you will have to edit it ensuring the correct format as mentioned in the first two lines of the file.

petestrash
27-05-2007, 06:53 PM
Here is a new postcodezones file with all the current codes.

Peter.

ajharvey
11-10-2007, 06:54 PM
Bizarrely enough it's still happening for me, even though Daylight savings has re-started.... I've kind of gotten used to the displayed times being an hour out. Everything still works, so it's just cosmetic, [and the times on the linux side of the fence are correct - this is only in the TiVO UI] but I have a new theory - I think the interface is following British DST (it's a Thompson Tivo running the NZ UK image)

When I first got the TIVO I couldn't use the UK image as the disk was too small, so I used one of the standard OZTivo ones. It's guided setup asked me about DST and I remember a big pointer to choose the NO DST option (presumable because OZ/NZTivo does it's timezones the Un*X way with tzdata files. I don't remember any such question in the UK Guided setup. It certainly isn't there if I re-run guided setup.

Is there anywhere else this setting could be? In MFS? The code must have dealt with UK summer time when it was a UK Tivo, I wonder if I have somehow re-activated some ancient code-path :-) Anyone know where the setting from US models guided setup is stored?

I am waiting to see if the time returns to normal when the UK comes of summer time in a few weeks....

catdog
12-10-2007, 04:39 AM
This is a stab in the dark, but try running

dbsetx /Setup TimeZone 0
dbsetx /Setup DaylightSavingsPolicy 0
reboot