Charlie
28-05-2004, 08:28 PM
I have had my Tivo for just over a week now and have tried everything to get it up and running. (I am a Tivo and Linux newbie - haven't hacked anything seriously since Dos 6.22)
I started with the " NZ TiVo Newbie? Start Here..." thread (thanks Jaidev and Tim) and managed to get the oztivo 3.1 image on and successfully networked it.
Then I tried the loadguide instructions (hadn't seen that the emulator was available). After editing and running all the tcls as per Tim's "Tivo Howto" I could not get past the Guided Setup. (I expected the Tivo to boot up and bypass the dial up because I read:
> Note that you don't need to do anything with the OzTivo guided setup
> onscreen because this is targeted for automating the setup to the OzTivo
> Service Emulator"
The Tivo insisted that I go through GS and then failed to connect.
Anyway, I eventually noticed the "Emulator available" thread (thanks Ed) so I re-imaged the disk (in case I had accidently hacked it to bits) and I followed Ed's instructions.
Again the Tivo fails to connect with the message "Failed. Service unavailable"
From the tivo I can successfully ping 66.238.88.163.
A few other things I have noticed that may be important:
When I select "Logs" from the Tivo Web I get:
INTERNAL SERVER ERROR
--cut here--
action_logs '/' ''
no files matched glob pattern "/var/log/O*"
while executing
"glob "$TIVO_ROOT/var/log/O*""
(procedure "::action_logs" line 20)
invoked from within
"::action_$action $chan $part $env"
("eval" body line 1)
invoked from within
"eval {::action_$action $chan $part $env}"
--cut here--
...before the list of logs displays.
The tvlog concerns me too - it has grown to about 172,000 records in the few hours I have had it on since re-imaging it. (With the old image it had built up to over 26 million records in about 5 days so I now switch the Tivo off unless I am working on it). I can't see any obvious error messages - mostly looks like debug information - but if anyone knows what I could look for I would be grateful.
Not sure if this matters but I do not have Sky (yet) - I have connected the Tivo to a VCR and want to try it out with Free To Air channels. I know I will need to sort out the IR codes but will cross that bridge later. Just using it as a manual recorder would be good to start with but I cannot get it to do anything.
Any hints would be much appreciated....
I started with the " NZ TiVo Newbie? Start Here..." thread (thanks Jaidev and Tim) and managed to get the oztivo 3.1 image on and successfully networked it.
Then I tried the loadguide instructions (hadn't seen that the emulator was available). After editing and running all the tcls as per Tim's "Tivo Howto" I could not get past the Guided Setup. (I expected the Tivo to boot up and bypass the dial up because I read:
> Note that you don't need to do anything with the OzTivo guided setup
> onscreen because this is targeted for automating the setup to the OzTivo
> Service Emulator"
The Tivo insisted that I go through GS and then failed to connect.
Anyway, I eventually noticed the "Emulator available" thread (thanks Ed) so I re-imaged the disk (in case I had accidently hacked it to bits) and I followed Ed's instructions.
Again the Tivo fails to connect with the message "Failed. Service unavailable"
From the tivo I can successfully ping 66.238.88.163.
A few other things I have noticed that may be important:
When I select "Logs" from the Tivo Web I get:
INTERNAL SERVER ERROR
--cut here--
action_logs '/' ''
no files matched glob pattern "/var/log/O*"
while executing
"glob "$TIVO_ROOT/var/log/O*""
(procedure "::action_logs" line 20)
invoked from within
"::action_$action $chan $part $env"
("eval" body line 1)
invoked from within
"eval {::action_$action $chan $part $env}"
--cut here--
...before the list of logs displays.
The tvlog concerns me too - it has grown to about 172,000 records in the few hours I have had it on since re-imaging it. (With the old image it had built up to over 26 million records in about 5 days so I now switch the Tivo off unless I am working on it). I can't see any obvious error messages - mostly looks like debug information - but if anyone knows what I could look for I would be grateful.
Not sure if this matters but I do not have Sky (yet) - I have connected the Tivo to a VCR and want to try it out with Free To Air channels. I know I will need to sort out the IR codes but will cross that bridge later. Just using it as a manual recorder would be good to start with but I cannot get it to do anything.
Any hints would be much appreciated....